#prop maker

Here is something I just made today when I got home from work. It is the Nuka Cola Quantum rolling ice box from Fallout Shelter that someone challenged me to make. Well, she didn’t challenge me, she just suggested it in a post! Hahaha! Someone else had mentioned it to me and I can’t remember who so I’m sorry I forgot who you are. The quarter is there for scale. I made the bottle using mighty putty, Sinatra and a hot glue cast for the cap. The ice box is sintra, wooden dowels for The legs, a cut up hot glue stick for the wheels, crushed fish tank quartz rocks and craft foam for the lid seal. Now I need to mold and cast the bottle and make necklaces or something. I hope y'all like it!

l1b3rtyprime.tumblr.com
Facebook.com/chunkanukeprops
#L1B3RTYPR1M3 on Instagram
#chunkanukeprops

Just finished up my Maria pistol from Fallout:New Vegas. I achieved this by using a Browning Hi-Power airsoft pistol, bondo, printable vellum, regular weight printer paper, amazing sculpt and rub-n-buff. It came out more gold than polished nickel since I failed to do a test area first. Oh well, I will Just have to make another one!

I just got back from vault 12 and have the Water Controller Chip! Damn that was a challenge! Hahaha. I just finished up the Water Chip from Fallout today. The main body is sintra and the rest is salvaged from a vintage standing wave indicator, an old corded telephone, a graphics card, a headphone jack, scrap electronics from my scrap bin, googly eyes,rubber feet from my Xbox parts bin and a Testors paint bottle. The power cord is temporary until I find the right vintage round plug and cord to use. I hope y'all like it!

I think I can pretty much call my Pip-Boy 2000 finished! I have the strap made but I’m just trying to find the right “sling rings” for it. I tried my hardest to not spend any money on this but, I had to buy 2 light bulbs to use as vacuum tubes and that was only 4 dollars so, not too bad. Now to list what I used. Scrap green sintra, various wires from my scrap electronics bin, a flip switch and light cover from an old wave length indicator, a female VGA connector, the screen is packaging plastic from a toy that I vac-formed , a sense from a trash Xbox connect sensor, balloon lights, a spare gear from a DVD player,various small screws, science fair poster board display lights, a magnet and some craft foam. I will take a video of it later on. I hope y'all like it as much as I do!

Here is a 3D printed Microfusion Cell my buddy sent to me a while back and I just finished it up. At least I think I’m finished with it? I can’t decide if I should weather it or not. Well, I have one more so maybe I will keep this one clean. For the paint I used Krylon OSHA safety yellow, Krylon OSHA black and Rustoleum Dark Steel. I didn’t have any water slide decal paper so I had to use Velum instead. Once I cut out the prints I had, I superglued them in place and then I applied two coats of Krylon Triple Thick clear glaze. Hope y'all like it.

Facebook.com/chunkanukeprops
L1B3RTYPR1M3 on Instagram

I just screen printed an Atom Cats design from page 331 out of The Art of Fallout 4 book. I have not screen printed in almost 15 years and now, I think I will pick back up on it again. I’m a pretty cranked cat daddy-o.

I just finished up The Gainer from Fallout 4 a bit ago. I used a toy revolver I found at Dollar General. I made the bull barrel using depron foam and a fat crayola marker cap, the handle is Foamular insulation foam and the rest is sintra, screws, a hobby knife grip, a heat sink from a tv I took apart and various knick-knacks. Hope y'all like it!

Here is my take on the Nuka Cola Thirst Zapper or what I like to call it, the Nuka Zapper from Fallout 4 that I made today. I made this using foamular insulation board, sintra, a fat crayola marker, a bottle cap, a sharpie magnum, o-rings, a printed logo covered in packaging tape and the fins on the barrel are hot glue casts. I will take better pictures tomorrow in the daylight. Hope y'all like it!
l1b3rtyprime.tumblr.com
Facebook.com/chunkanukeprops
L1BERTYPR1M3 on instagram

I just finished up a can of Deezer’s Lemonade from Fallout 4. I made this using a cut up Pringles can, some gray and brown paper, masking tape, a black sharpie and a yellow paint pen then of course some good ol’ weathering with black and brown acrylic paint and burnt sienna for some rust effects. The wiki image is a little faded compared to the in game image so that’s why the lemonade paper is as brown as it is.

Proceso de “aputrefaccionamiento” de un simple esqueleto de plástico. Con latex, pinturas, pelaje, paciencia y amor, sobre todo. 

https://www.instagram.com/zeballosaxel_/     for moreeee!